PSU 6-200 - 1200W Single Channel Programmable Switching DC Power Supply
The PSU-Series is a single output programmable switching DC power supply covering a power range up to 1520W. This Series of products include five models with the combination from 6V to 60V rated voltages. As th ePSU-series can be connected in series for maximum 2 units or in parallel for maximum 4 units, capacity of connecting multiple PSU-Series units for higher voltage or higher current output provides a broad coverage of applications.
The C.V / C.C priority selection of the PSU-Series is a very useful features for DUT protection. The conventional power supply normally operates under C.V mode when the power supply is turned on. This could bring a high inrush current to the capacitive load or current-intensive load at the power output on stage. Though the current becomes stable after the C.C mode is activated, the current spike occurred at the C.V and C.C crossover point may possibly damage the DUT. At the power output on stage, the PSU-Series is able to run under C.C priority to limit the current spike occurred at the threshold voltage and therefore protects DUT from the inrush current damage.
The OVP and OCP protections can prevent the DUT damage. Both OVP and OCP levels can be selected the range of 10% to 110%, with the default level set at 110%, of the rated voltage / current of the power supply. THe PSU-Series provides USB Host / Device , LAN, RS-232 with RS-485 and Analog Control Interfaces as standard. The LabView driver is available at the rear panel for external control of the power On/ Off and the external monitoring of the power output voltagre and current.
- Voltage Rating:6V/12.5V/20V/40V/60V
- Output Power Rating: 1200W~1520W
- C.V / C.C Priority ; Particularly Suitable for the Batterey & LED industry
- Adjustable Slew Rate
- Series and Parallel operation (2 Units in Series or 4 units in parallel)
- High Efficiency and High Power Density
- 19 Inch Rack Mount Size Design
- Stabdard Interface: LAN, RS-232 & RS-485, USB(Device / Host), Analog Control Interface
- Optional Interface:GPIB, Analog Control Interface(Isolated Voltage Control), Analog Control Interface(Isolated Current Control)
| Output Rating | |
| Voltage | 0~6V |
| Current | 0~200A |
| Power | 1200W |
| Output Ripple and Noise | |
| CV p-p (10~20MHz) | 60mV |
| CV rms (5Hz ~1MHz) | 8mV |
| CC rms (5Hz~1MHz) | 400mA |
| Load Regulation (Change from 10% to 90% of full load) | |
| Voltage (0.01% of F.S. + 2mV) | 2.6mV |
| Current (0.02% of F.S + 5mA) | 45mA |
| Line Regulation (Change from 85 to 132 VAC input or 170-265 VAC) | |
| Voltage(0.01% of F.S. + 2mV) | 2.6mV |
| Current(0.01% of F.S. + 2mA) | 22mA |
| Programming Accuracy | |
| Voltage 0.05% + offset (mV) | 3mV |
| Current 0.2% + offset(mA) | 200mA |
| Measurement Accuracy | |
| Voltage 0.1% + offset (mV) | 6mV |
| Current 0.2% + offset (mA) | 400mA |
| Load Transient Recover Time | |
| Time | 1.5ms |
| Output Response Time | |
| Rise Time (No Load & Full Load) | 80ms |
| Fall Time (No Load) | 500ms |
| Fall Time (Full Load) | 10ms |
| Programming / Measurement Resolution | |
| Voltage | 0.2mV |
| Current | 6mA |
| Temperature Coefficient (after 30 minutes warm up) | |
| Voltage | 100ppm/˚C after 30 minutes warm up |
| Current | 100ppm/˚C after 30 minutes warm up |
| Series and Parallel Operation | |
| Parallel Operation | Up to 4 Units Including Master Unit |
| Series Operation | Up to 2 Units Including Master Unit |
| Environment Conditions | |
| Environment | Indoor use, installation category II (AC Input), polution degree 2 |
| Operating Temperature Range | 0˚C ~50˚C |
| Storage Temperature Range | -25˚C~70˚C |
| Operating Humidity Range | 20% to 85% RH |
| Storage Humidity Range | Up to 90% or less relative humidity (no condensation) |
| AC Input | |
| Normal Input | 100VAC to 240VAC, 50Hz to 60Hz, single phase |
| Input Range | 85VAC~265VAC |
| Power Factor (100VAC / 200VAC) | 0.99 / 0.98 |
| Maximum Input Current (100VAC / 200VAC) | 21A / 11A |
| Inrush Current | ≤ 50A |
| Efficiency (100VAC / 200VAC) | 77% / 79% |
| Other | |
| Analog Control (Non-Isolated) | Yes |
| PC Remote Interface (standard) | USB (Device / Host) RS-232 with RS-485 / LAN |
| (Optional) | GPIB / Analog Control Interface (Isolated Voltage Control) / Analog Control Interface (Isolated Current Control; Note: Select one of the three |
| Cooling Fan | Forced air cooling by internal fan |
| Dimensions & Weight | 422.8 (W) x 43.6 (H) x 432.8 (D); Approx 8.7kg |
Do you have a 1200W Single Channel Programmable Switching DC Power Supply that needs to be calibrated?
We offer standard traceable calibration and ISO 17025 accredited calibration services.
Get your 1200W Single Channel Programmable Switching DC Power Supply calibrated today! Click Here!Recommended Accessories for the 1200W Single Channel Programmable Switching DC Power Supply
USB Cable, USB 2.0, A-B Type, 1200mm
PSE power cord,3M
RS485 Cable with DB9 connector kit
